Skip header and navigation

Refine By

   MORE

56 records – page 1 of 6.

Asepto wound and irrigating syringe

https://mhc.andornot.com/en/permalink/artifact4794
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003216
Description
Asepto irrigating syringe, which consists of a hollow glass barrel with a pointed catheter tip and a round, hollow red rubber squeeze bulb at its top; the glass barrel has a small round opening at its pointed tip, and a larger round opening at its wider, lipped end; the rubber bulb is inserted into…
  1 image  
Accession Number
000003216
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Irrigation -- syringe
Description
Asepto irrigating syringe, which consists of a hollow glass barrel with a pointed catheter tip and a round, hollow red rubber squeeze bulb at its top; the glass barrel has a small round opening at its pointed tip, and a larger round opening at its wider, lipped end; the rubber bulb is inserted into this end; a round opening is visible at the bottom end of the rubber bulb.
Number Of Parts
1
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton-Dickinson
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item identified in a 1960s catalogue
Material
glass: clear
rubber: red
Inscriptions
On the side of the red rubber bulb, raised rubber letters read, "ASEPTO // TRADE MARK // 1½ OZ // B-D" and at the top, "BECTON, DICKINSON & CO. // RUTHERFORD, N.J. // PAT. 2,086,925" inside a circle.
Permanent Location
Storage Room 0010
0010-D5-14
Dimension Notes
Length 22.2 cm x Diam. 5.5 cm
Condition Remarks
The syringe showed minor signs of wear; there were no major scratches of breaks, and the rubber seemed stable; it was slightly dusty along its top rim, and there was a thin, white residue on the inner surface, possibly water spots; #2: rubber - may require special treatment.
Copy Type
Original
Reference Types
Book
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 177 (similar to item #6H-594-1) (see attached photocopy); CD #3
Images
Less detail

Asepto wound and irrigating syringe

https://mhc.andornot.com/en/permalink/artifact4796
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003218
Description
Asepto irrigating syringe, which consists of a hollow glass barrel with a pointed catheter tip and a round, hollow red rubber squeeze bulb at its top; the glass barrel has a small round opening at its pointed tip, and a larger, lipped opening at its wider end; the rubber bulb is inserted into this …
  2 images  
Accession Number
000003218
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Irrigation -- syringe
Description
Asepto irrigating syringe, which consists of a hollow glass barrel with a pointed catheter tip and a round, hollow red rubber squeeze bulb at its top; the glass barrel has a small round opening at its pointed tip, and a larger, lipped opening at its wider end; the rubber bulb is inserted into this end; a round opening is visible at the bottom end of the rubber bulb.
Number Of Parts
1
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton-Dickinson
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item identified in a 1960s catalogue
Material
glass: clear
rubber: red
Inscriptions
On the side of the red rubber bulb, raised rubber letters read, "ASEPTO // TRADE MARK // 3 OZ // B-D" and at the top, "BECTON, DICKINSON & CO. // RUTHERFORD, N.J. // PAT. 2,086,925" inside a circle; on top of the bulb in black marker is the number "12".
Permanent Location
Storage Room 0010
0010-D5-14
Dimension Notes
Length 26.7 cm x Diam. 6.5 cm
Condition Remarks
The glass barrel of the syringe was in very good condition, with no breaks, chips or scratches; the rubber bulb was deteriorating; the part inserted into the barrel was crumbling, leaving an orange deposit on the inner surface of the glass; there were cracks developing on the rest of its surface; there was a thin, white film on the inner surface of the barrel, possibly water stains; #2: rubber - may require special treatment.
Copy Type
Original
Reference Types
Book
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 177 (similar to item #6H-594-3) (see attached photocopy); CD #4
Images
Less detail

Asepto wound and irrigating syringe

https://mhc.andornot.com/en/permalink/artifact4797
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003219 a-b
Description
Asepto irrigating syringe, which consists of a hollow glass barrel (a) with a pointed catheter tip and a round, hollow red rubber squeeze bulb (b) at its top; the glass barrel has a small round opening at its pointed tip, and a larger round opening at its wider, lipped end; the rubber bulb is inser…
  2 images  
Accession Number
000003219 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Irrigation -- syringe
Description
Asepto irrigating syringe, which consists of a hollow glass barrel (a) with a pointed catheter tip and a round, hollow red rubber squeeze bulb (b) at its top; the glass barrel has a small round opening at its pointed tip, and a larger round opening at its wider, lipped end; the rubber bulb is inserted into this end; a round opening is visible at the bottom end of the rubber bulb.
Number Of Parts
2
Part Names
a - syringe barrel - Size: Length 16.7 cm x Diam. 3.9 cm
b - rubber bulb - Size: Length 6.8 cm x Diam. 5.0 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton-Dickinson
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item identified in a 1960s catalogue
Material
glass: clear
rubber: red
Inscriptions
On the side of the red rubber bulb, raised rubber letters read, "ASEPTO // TRADE MARK // 1 OZ // B-D" and at the top, "BECTON, DICKINSON & CO. // RUTHERFORD, N.J. // PAT. 2,086,925" inside a circle.
Permanent Location
Storage Room 0010
0010-D5-14
Condition Remarks
The syringe showed minor signs of wear; there were no major scratches of breaks, and the rubber seemed stable; it was slightly dusty along its top rim, and there was a thin, white residue on the inner surface, possibly water spots; #2: rubber - may require special treatment.
Copy Type
Original
Reference Types
Book
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 177 (similar to item #6H-594-1) (see attached photocopy); CD #4
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4826
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003248 a-b
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flatten…
  1 image  
Accession Number
000003248 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flattened anti-roll sides; the plunger (b) is a hollow, frosted glass cylinder with a flat bottom and a small, round, flat thumb-push on top.
Number Of Parts
2
Part Names
a - barrel - Size: Length 7.5 cm x Width 1.7 cm x Depth 1.5 cm
b - plunger- Size: Length 6.3 cm x Diam. 1.5 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item in 1960 catalogue
Material
metal: silver
glass: clear; frosted
Inscriptions
On the outer side of the barrel, yellow-brown printing reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed by two rows of short and long increment lines, one row interspersed with, "½ // 1 // 1½ // 2 cc" and the other by "10 // 20 // 30 m"; a symbol that looks like a leaf with "B-D" superimposed appears beside the increment lines, and also near the thumb-push end of the plunger.
Permanent Location
Storage Room 0010
0010-D5-2
Condition Remarks
All parts move freely; there were slight signs of wear; there was no corrosion, and no chips, breaks or large scratches; the inner surface of the barrel had some scratches.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-2CM/B) (see attached photocopy); also see 000.003.249 and .250; CD #4
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4827
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003249 a-b
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flatten…
  1 image  
Accession Number
000003249 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flattened anti-roll sides; the plunger (b) is a hollow, frosted glass cylinder with a flat bottom and a small, round, flat thumb-push on top.
Number Of Parts
2
Part Names
a - barrel - Size: Length 7.5 cm x Width 1.7 cm x Depth 1.5 cm
b - plunger- Size: Length 6.3 cm x Diam. 1.5 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item in 1960 catalogue
Material
metal: silver
glass: clear; frosted
Inscriptions
On the outer side of the barrel, yellow-brown printing reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed by two rows of short and long increment lines, one row interspersed with, "½ // 1 // 1½ // 2 cc" and the other by "10 // 20 // 30 m"; a symbol that looks like a leaf with "B-D" superimposed appears beside the increment lines, and also near the thumb-push end of the plunger.
Permanent Location
Storage Room 0010
0010-D5-2
Condition Remarks
All parts move freely; there were some scratches on the inner surface of the barrel; there was no corrosion; there were no chips, breaks, or long scratches.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-2CM/B) (see attached photocopy); also see 000.003.249 and .250; CD #4
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4828
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003250 a-b
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flatten…
  1 image  
Accession Number
000003250 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, consisting of (a) a hollow, glass cylindrical barrel that is open at both ends; the tip is cylindrical metal and has a luer-lok system to hold the needle in the small, round opening; the opposite end has a large, round opening with a round protruding lip with two flattened anti-roll sides; the plunger (b) is a hollow, frosted glass cylinder with a flat bottom and a small, round, flat thumb-push on top.
Number Of Parts
2
Part Names
a - barrel - Size: Length 7.5 cm x Width 1.7 cm x Depth 1.5 cm
b - plunger- Size: Length 6.3 cm x Diam. 1.5 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar to item in 1960 catalogue
Material
metal: silver
glass: clear; frosted
Inscriptions
On the outer side of the barrel, yellow-brown printing reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed by two rows of short and long increment lines, one row interspersed with, "½ // 1 // 1½ // 2 cc" and the other by "10 // 20 // 30 m"; a symbol that looks like a leaf with "B-D" superimposed appears beside the increment lines, and also near the thumb-push end of the plunger.
Permanent Location
Storage Room 0010
0010-D5-2
Condition Remarks
All parts move freely; there were some scratches on the inner surface of the barrel; there was no corrosion; there were no cracks, breaks, or large scratches.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-2CM/B) (see attached photocopy); also see 000.003.249 and .250; CD #4
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4917
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003305 a-b
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is …
  2 images  
Accession Number
000003305 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is a small hole at the end of the tip; the barrel fits into the wider end; it is cylindrical, with two flat, closed ends; one end has a straight extending glass lip; the body of the plunger is frosted glass; the opposite end is blunt; the plunger is hollow.
Number Of Parts
2
Part Names
a - barrel - Size: Length 14.0 cm x Width 3.7 cm x Depth 3.2 cm
b - plunger - Size: Length 13.9 cm x Diam. 3.0 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (Country)
United States of America
Material
glass: clear; frosted
metal: silver
Inscriptions
Brown transfer ink on the side of the barrel reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed on the opposite side by "5 // 10 // 15 // 20 // 25 // 30cc" set alongside one tow of short and long increment lines; a logo, a maple leaf design with "B-D" in the centre, is printed below this row.
Permanent Location
Storage Room 0010
0010-D5-1
Condition Remarks
The metal parts showed no signs of corrosion; there were no chips or breaks; there were slight scratches on the inner surface of the barrel; the syringe was slightly dusty.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-30YL) (see attached photocopy); see also 000.003.306 and .307; CD #3
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4918
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003306 a-b
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is …
  2 images  
Accession Number
000003306 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is a small hole at the end of the tip; the barrel fits into the wider end; it is cylindrical, with two flat, closed ends; one end has a straight extending glass lip; the body of the plunger is frosted glass; the opposite end is blunt; the plunger is hollow.
Number Of Parts
2
Part Names
a - barrel - Size: Length 14.0 cm x Width 3.7 cm x Depth 3.2 cm
b - plunger - Size: Length 13.9 cm x Diam. 3.0 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (Country)
United States of America
Material
glass: clear; frosted
metal: silver
Inscriptions
Brown transfer ink on the side of the barrel reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed on the opposite side by "5 // 10 // 15 // 20 // 25 // 30cc" set alongside one tow of short and long increment lines; a logo, a maple leaf design with "B-D" in the centre, is printed below this row.
Permanent Location
Storage Room 0010
0010-D5-1
Condition Remarks
The metal parts showed no signs of corrosion; there were no chips or breaks; there were slight scratches on the inner surface of the barrel; the syringe was slightly dusty.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-30YL) (see attached photocopy); see also 000.003.305 and .307; CD #3
Images
Less detail

B-D Ace hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact4919
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003307 a-b
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is …
  3 images  
Accession Number
000003307 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D Ace hypodermic syringe, which consists of a barrel (a) and a plunger (b); the barrel is hollow and cylindrical; one end has a circular opening with a flat, open lip and two flat anti-roll sides; the other end tapers to form a point, and is topped with a cylindrical metal luer-lok tip; there is a small hole at the end of the tip; the barrel fits into the wider end; it is cylindrical, with two flat, closed ends; one end has a straight extending glass lip; the body of the plunger is frosted glass; the opposite end is blunt; the plunger is hollow.
Number Of Parts
2
Part Names
a - barrel - Size: Length 14.0 cm x Width 3.7 cm x Depth 3.2 cm
b - plunger - Size: Length 13.9 cm x Diam. 3.0 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson & Co.
Site Made (Country)
United States of America
Material
glass: clear; frosted
metal: silver
Inscriptions
Brown transfer ink on the side of the barrel reads, "ACE // Becton, Dickinson & Co. [cursive] // MADE IN U.S.A." followed on the opposite side by "5 // 10 // 15 // 20 // 25 // 30cc" set alongside one tow of short and long increment lines; a logo, a maple leaf design with "B-D" in the centre, is printed below this row.
Permanent Location
Storage Room 0010
0010-D5-1
Condition Remarks
The metal parts showed no signs of corrosion; there were no chips or breaks; there were slight scratches on the inner surface of the barrel; the syringe was slightly dusty.
Copy Type
Original
Reference Types
Book
Other
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-30YL) (see attached photocopy); see also 000.003.305 and .306; CD #4
Images
Less detail

B-D luer-lok multifit hypodermic syringe

https://mhc.andornot.com/en/permalink/artifact5079
Dates
1960
circa 1960
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
Accession Number
000003327 a-b
Description
B-D luer-lok multifit hypodermic syringe, which consists of a hollow, ground-glass plunger (b) that slides into a graduated 10-cc glass barrel (a) that tapers to a metal luer-lok tip; the luer-lok tip accomodates and locks the needle into place; the other end has a prominent lip with two flattened,…
  2 images  
Accession Number
000003327 a-b
Collection
Rockwood / Kingston Psychiatric Hospital / Providence Continuing Care Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Treatment, General
MeSH Heading
Syringes
MM= Injections -- hypodermic syringe
Description
B-D luer-lok multifit hypodermic syringe, which consists of a hollow, ground-glass plunger (b) that slides into a graduated 10-cc glass barrel (a) that tapers to a metal luer-lok tip; the luer-lok tip accomodates and locks the needle into place; the other end has a prominent lip with two flattened, anti-roll sides; the glass plunger has a flat tip and a small, round, flat thumb push at the top.
Number Of Parts
2
Part Names
a - barrel - Size: Length 11.5 cm x Width 2.8 cm x Depth 2.3 cm
b - plunger - Size: Length 10.8 cm x Diam. 1.9 cm
Provenance
Used at the Kingston Psychiatric Hospital
Maker
Becton, Dickinson
Site Made (City)
Rutherford
Site Made (State)
New Jersey
Site Made (Country)
United States of America
Dates
1960
circa 1960
Date Remarks
Similar item identified in 1960s catalogue
Material
metal: silver
glass: clear; frosted
Inscriptions
Printed on the glass barrel: " 2 4 6 8 10CC // mtz [the "m" superscripted, the "z" subscripted] // B-D LUER-LOK // MULTIFIT // MADE IN U.S.A. // S"; printed on the plunger: "mtz [the "m" superscripted, the "z" subscripted]"
Permanent Location
Storage Room 0010
0010-D5-1
Condition Remarks
The plunger was stuck in the barrel; the syringer showed only minor signs of wear
Copy Type
Original
Reference Types
Book
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 284 (similar to item #6-10YL) (see attached photocopy); CD #3
Research Facts
Arrived in metal steritube 000.003.326
Images
Less detail

56 records – page 1 of 6.