Skip header and navigation

Refine By

   MORE

82 records – page 1 of 9.

acetabular component (cup)

https://mhc.andornot.com/en/permalink/artifact5026
Dates
1990
circa 1990
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001003007
Description
Acetabular component, which consists of a concave metal cup with and open top and seven round holes through the metal; the outside edges of the cup are slightly rough; the inside edges are smooth; the top upper edge is smooth and there is a groove line in the circumference of the inner metal just b…
  2 images  
Accession Number
001003007
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
Acetabular component, which consists of a concave metal cup with and open top and seven round holes through the metal; the outside edges of the cup are slightly rough; the inside edges are smooth; the top upper edge is smooth and there is a groove line in the circumference of the inner metal just below the top upper edge; materials: titanium, aluminum, vanadium alloy.
Number Of Parts
1
Provenance
Research material used at the Human Mobility Research Centre.
Dates
1990
circa 1990
Material
metal: grey
Inscriptions
None
Permanent Location
Storage Room 0010
0010-E2-5
Dimension Notes
Depth 2.4 cm x Diam. 5.8 cm
Condition Remarks
The metal shows minor wear only; no corrosion is visible.
Copy Type
Original
Reference Types
Book
Person
JPG
Reference Comments
Dr. Charles Sorbie; "Annual Product Catalogue," by Howmedica International, 1992, p. A50 (see attached photocopy); CD #4
Research Facts
This titanium alloy was originally developed for the aircraft industry; the cup would have been used with a polyethylene insert; the holes were used to screw into the acetabulum when there was a concern about its stability; the hole at the bottom of the cup was used to make sure that the component had been hammered right against the bone; the rough exterior finish was for a better grip.
Exhibit History
"Joint Ventures," Museum of Health Care, Nov. 19, 2001-Jan. 2013
Images
Less detail

Austin Moore type hip prosthesis 1¾"

https://mhc.andornot.com/en/permalink/artifact4976
Dates
1958
circa 1958
Collection
Dr. Charles Sorbie Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001002002
Description
Austin Moore type hip prosthesis, which consists of a spherical cobalt chromium alloy femoral head that has an attached long triangular stem with two fenestrations at its wide end and a round hole through the metal at the base of the head; the shaft of the stem has smooth sides and a slightly round…
  2 images  
Accession Number
001002002
Collection
Dr. Charles Sorbie Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
Austin Moore type hip prosthesis, which consists of a spherical cobalt chromium alloy femoral head that has an attached long triangular stem with two fenestrations at its wide end and a round hole through the metal at the base of the head; the shaft of the stem has smooth sides and a slightly rounded outer edge; the sphere is reflective, while the stem is dull in appearance.
Number Of Parts
1
Provenance
Used at Kingston General Hospital by Dr. Charles Sorbie
Dates
1958
circa 1958
Material
metal: silver
Inscriptions
One side of the stem has "316L R ["R" enclosed in a square] 1¾" DIA. 2C396" etched into the metal.
Permanent Location
Storage Room 0010
0010-E2-4
Dimension Notes
Length 12.0 cm x Width 5.8 cm x Depth 3.8 cm
Condition Remarks
The metal shows a good deal of wear; there are several deep gouges, especially at the base of the head and the top of the stem; no corrosion is visible.
Copy Type
Original
Reference Types
Book
Person
JPG
Reference Comments
"Hospital and Physicians Equipment and Supplies," the J.F. Hartz Co., 1960, p. 98 (similar to item marked) (see attached photocopy); Dr. Charles Sorbie; CD #3
Research Facts
This type of prosthesis was cast in two parts and has a hollow head; the fenestrations in the stem were to allow for bone growth around the prosthesis; the hole at the top was for a hook for removal; this type of prosthesis did not work too well.
Images
Less detail

BiPolar component

https://mhc.andornot.com/en/permalink/artifact5051
Dates
1980
circa 1980
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001003032
Description
BiPolar component, which consists of a concave cobalt chromium alloy cup with a wide, round open top; the outer edges are smooth and rounded; the inside of the cup has a concave polyethylene liner that fits tightly against the metal piece; the inside of the polyethylene liner has smooth sides and a…
  1 image  
Accession Number
001003032
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
BiPolar component, which consists of a concave cobalt chromium alloy cup with a wide, round open top; the outer edges are smooth and rounded; the inside of the cup has a concave polyethylene liner that fits tightly against the metal piece; the inside of the polyethylene liner has smooth sides and a round, open top; the upper edges are fairly thin and flat.
Number Of Parts
1
Provenance
Research material used at the Human Mobility Research Centre.
Dates
1980
circa 1980
Material
metal: silver
polyethylene: off-white
Inscriptions
The outside edge of the cup has "FRANCOBAL S A0 [with a slash through it] 60 NM" etched into the metal near the top.
Permanent Location
Storage Room 0010
0010-E2-5
Dimension Notes
Depth 4.1 cm x Diam. 5.6 cm
Condition Remarks
The metal shows some wear, but no corrosion is visible; the polyethylene shows minor wear only; no staining is visible.
Copy Type
Original
Reference Types
Book
Person
JPG
Reference Comments
Dr. Charles Sorbie; "1992 Annual Product Catalogue," by Howmedica Inc., Orthopedics Division, 1992, pp. A-35 (see attached photocopy); CD #3
Research Facts
Thisis an early BiPolar hip replacement; it was used against a steel femoral head--most likely with a Moore type hip prosthesis; also known as an interpositional cup.
Images
Less detail

BiPolar component with P.C.A. femoral head component

https://mhc.andornot.com/en/permalink/artifact5027
Dates
1980
circa 1980
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001003008 a-b
Description
BiPolar vitallium component with P.C.A. femoral head; the BiPolar component (a) consists of a concave metal cup with an open top; the outside eges are smooth and rounded; the inside of the cup has a concave polyethylene liner; the liner fits tightly against the BiPolar component; the inside of the …
  2 images  
Accession Number
001003008 a-b
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
BiPolar vitallium component with P.C.A. femoral head; the BiPolar component (a) consists of a concave metal cup with an open top; the outside eges are smooth and rounded; the inside of the cup has a concave polyethylene liner; the liner fits tightly against the BiPolar component; the inside of the liner has thick sides and a concave opening with an open top and smooth edges; a P.C.A. femoral head (b) fits tightly into the liner; the femoral head consists of a single spherical piece of metal with a round, hollow centre and a flattened base; the base has an open centre.
Number Of Parts
2
Part Names
a - BiPolar component - Size: Depth 3.9 cm x Diam. 5.1 cm
b - P.C.A. femoral head - Size: Depth 2.7 cm x Diam. 2.8 cm
Provenance
Research material used at the Human Mobility Research Centre.
Dates
1980
circa 1980
Material
metal: silver
polyethylene: off-white
Inscriptions
(a) None; (b) the base of the femoral head has, "VITALLIUM 6284 - 0 - 232 32 MM + 5 MM JNEDU" etched into the metal.
Permanent Location
Storage Room 0010
0010-E2-5
Condition Remarks
The metal shows minor wear only; no corrosion is visible; the polyethylene shows minor wear only.
Copy Type
Original
Reference Types
Book
Person
JPG
Reference Comments
Dr. Charles Sorbie; "Annual Product Catalogue," by Howmedica International, 1992, pp. A3 and A35 (see attached photocopies); CD #4
Research Facts
The BiPolar component is still used to treat broken hips; the P.C.A. (porus coated anatomic) system is modular and has detachable femoral head components.
Exhibit History
"Joint Ventures," Museum of Health Care, Nov. 19, 2001-Jan. 2013
Images
Less detail

cement restrictor inserter

https://mhc.andornot.com/en/permalink/artifact10930
Dates
1993
circa 1993
Collection
Kingston General Hospital Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
004029004
Description
A cement restrictor inserter; T shaped; consists of a handle which is made of a short metal shaft, and a long shaft which extends at 90 degrees from the handle with a threaded screw like end; calibrated in centimeters from 10 to 25.
  1 image  
Accession Number
004029004
Collection
Kingston General Hospital Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
A cement restrictor inserter; T shaped; consists of a handle which is made of a short metal shaft, and a long shaft which extends at 90 degrees from the handle with a threaded screw like end; calibrated in centimeters from 10 to 25.
Number Of Parts
1
Provenance
Used for hip replacement surgery at KGH.
Maker
Depuy
Site Made (City)
Warsaw
Site Made (State)
Indiana
Site Made (Country)
United States of America
Dates
1993
circa 1993
Date Remarks
Appears in a 1993 Depuy catalogue.
Material
metal: silver
Inscriptions
"Depuy 5460-02" printed on the handle.
Permanent Location
Storage Room 0010
0010-E2-9
Dimension Notes
Length 31.3 cm x Width 7.5 cm x Depth 1.2 cm
Condition Remarks
Some minor wear.
Copy Type
Original
Reference Types
Book
JPG
Reference Comments
"DePuy Product Portfolio, Instruments," Warsaw, Indiana, 1993, p. 68 (see attached photocopy); CD #7
Research Facts
This device is used to position either the cement restrictor trials or implants at the distal end of the medullary canal; the screw at the end attaches to the threaded holes in 004.029.003.
Images
Less detail

cement restrictor trial set

https://mhc.andornot.com/en/permalink/artifact10929
Dates
1993
circa 1993
Collection
Kingston General Hospital Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
004029003 a-g
Description
A set of trial cement restrictors which are small cylindrical metal objects with screw holes on the tops and bottoms; each tapers slightly towards the top.
  1 image  
Accession Number
004029003 a-g
Collection
Kingston General Hospital Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
A set of trial cement restrictors which are small cylindrical metal objects with screw holes on the tops and bottoms; each tapers slightly towards the top.
Number Of Parts
7
Part Names
a - cement restrictor trial - Size: Length 1.7 cm x Diam. 0.7 cm
b - cement restrictor trial - Size: Length 1.8 cm x Diam. 0.9 cm
c - cement restrictor trial - Size: Length 2.1 cm x Diam. 1.1 cm
d - cement restrictor trial - Size: Length 2.1 cm x Diam. 1.4 cm
e - cement restrictor trial - Size: Length 2.1cm x Diam. 1.6 cm
f - cement restrictor trial - Size: Length 2.2 cm x Diam. 1.9 cm
g - cement restrictor trial - Size: Length 1.7 cm x Diam. 0.7 cm
Provenance
They were used for hip replacement surgery at KGH.
Maker
Depuy
Site Made (City)
Warsaw
Site Made (State)
Indiana
Site Made (Country)
United States of America
Dates
1993
circa 1993
Date Remarks
Appear in a 1993 Depuy catalogue.
Material
metal: silver
Inscriptions
Each device has a number from 1-7 printed on the bottom, increasing with size.
Permanent Location
Storage Room 0010
0010-E2-9
Condition Remarks
Like new.
Copy Type
Original
Reference Types
Book
Internet
JPG
Reference Comments
"DePuy Product Portfolio, Reconstructive Products," Warsaw, Indiana, 1993, p. 9 (see attached photocopy); "DePuy Product Portfolio, Instruments," Warsaw, Indiana, 1993, p. 68 (see attached photocopy).
"Internet: Isotis: Tissue Engineers"; CD #7
Research Facts
These devices are used for determining the proper fit for the real cement restrictors which would be used in hip replacement surgery to keep the cement from leaking down the femur shaft.
Images
Less detail

Charnley femoral rasp

https://mhc.andornot.com/en/permalink/artifact3316
Dates
1975
1985
circa 1975-1985
Collection
Kingston General Hospital Operating Room Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
997034008
Description
Angled one-piece handle has six holes and is mounted on a tray-like flat bottom; rasp end is angled and wide at handle, narrowing towards tip; vitallium rasp has grooved, roughened, sharp, serrated surface, including tip and sides; there are groove-like indentations 2.5 cm proximal to handle on bo…
  1 image  
Accession Number
997034008
Collection
Kingston General Hospital Operating Room Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Hip Prosthesis -- instrumentation
MM= Cutting Tool -- raspatory
Description
Angled one-piece handle has six holes and is mounted on a tray-like flat bottom; rasp end is angled and wide at handle, narrowing towards tip; vitallium rasp has grooved, roughened, sharp, serrated surface, including tip and sides; there are groove-like indentations 2.5 cm proximal to handle on both sides
Number Of Parts
1
Provenance
Used in the Kingston General Hospital Operating Room.
Maker
Downs
Site Made (Country)
England
Dates
1975
1985
circa 1975-1985
Material
metal: silver
Inscriptions
Handle has the number "6732" stamped into the metal; beneath the number is a "V" inside a heart-shaped ring stamped into the metal
Permanent Location
Storage Room 0010
0010-E2-7
Dimension Notes
Length 25.5 cm x Width 6.2 cm x Depth 4.3 cm
Condition Remarks
Tray-like flat bottom shows wear and tear; scrapes and dents are visible
Copy Type
Original
Reference Types
Book
Reference Comments
"Surgical Instruments and Hospital Equipment," 23rd ed., Downs Surgical PLC, ca. 1982, p. G16 (similar to item GB-115-01-M)
Research Facts
Femoral shaft evacuation; total hip surgery
Images
Less detail

Charnley femoral rasp

https://mhc.andornot.com/en/permalink/artifact3317
Dates
1975
1985
circa 1975-1985
Collection
Kingston General Hospital Operating Room Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
997034009
Description
Angled one-piece handle has six holes and is mounted on a tray-like flat bottom; vitallium rasp end is angled and wide at handle, narrowing towards tip; rasp has grooved, roughened, sharp, serrated surface, including tip and sides; there are groove-like indentations 2.5 cm proximal to handle on bot…
  1 image  
Accession Number
997034009
Collection
Kingston General Hospital Operating Room Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Hip Prosthesis -- instrumentation
MM= Cutting Tool -- raspatory
Description
Angled one-piece handle has six holes and is mounted on a tray-like flat bottom; vitallium rasp end is angled and wide at handle, narrowing towards tip; rasp has grooved, roughened, sharp, serrated surface, including tip and sides; there are groove-like indentations 2.5 cm proximal to handle on both sides
Number Of Parts
1
Provenance
Used in the Kingston General Hospital Operating Room.
Maker
Downs
Site Made (Country)
England
Dates
1975
1985
circa 1975-1985
Material
metal: silver
Inscriptions
Handle has the number "6730" stamped into the metal; beneath the number is a "V" inside a heart-shaped ring stamped into the metal
Permanent Location
Storage Room 0010
0010-E2-7
Dimension Notes
Length 25.5 cm x Width 6.2 cm x Depth 4.3 cm
Condition Remarks
Tray-like flat bottom shows wear and tear; scrapes and dents are visible
Copy Type
Original
Reference Types
Book
Reference Comments
"Surgical Instruments and Hospital Equipment," 23rd ed., Downs Surgical PLC, ca. 1982, p. G16 (similar to item GB-115-01-M)
Research Facts
Femoral shaft evacuation; total hip surgery
Images
Less detail

Charnley hip prosthesis

https://mhc.andornot.com/en/permalink/artifact4985
Dates
1961
circa 1961
Collection
Dr. Charles Sorbie Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001002011
Description
Charnley hip prosthesis, which consists of a small solid spherical femoral head attached to a cylindrical base; the bottom of the base joins with a long triangular stem; the stem is made of solid metal, with four sides, rounded edges, and a rounded end.
  1 image  
Accession Number
001002011
Collection
Dr. Charles Sorbie Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
Charnley hip prosthesis, which consists of a small solid spherical femoral head attached to a cylindrical base; the bottom of the base joins with a long triangular stem; the stem is made of solid metal, with four sides, rounded edges, and a rounded end.
Number Of Parts
1
Provenance
Used at Kingston General Hospital by Dr. Charles Sorbie
Maker
Thakray
Dates
1961
circa 1961
Date Remarks
This type of prosthesis was first implanted in 1959, but began in earnest in 1961
Material
metal: silver
Inscriptions
One side of the stem has, "THAKRAY // 121 - 78SR" etched into the metal.
Permanent Location
Storage Room 0010
0010-E2-5
Dimension Notes
Length 14.5 cm x Width 6.4 cm x Depth 6.2 cm
Condition Remarks
The metal shows wear; there are several deep gouges at the top of the stem; no corrosion is visible.
Copy Type
Original
Reference Types
Person
JPG
Reference Comments
Dr. Charles Sorbie; CD #4
Research Facts
This hip prosthesis was designed by Sir John Charnley; it was the first of its kind of hip joint, with a (22 mm) smaller head designed for less wear on the socket; this type of prosthesis was originally used with Teflon sockets, 2/3 of which wore out within six months; these were replaced with high-density polyethylene sockets.
Exhibit History
"Joint Ventures," Museum of Health Care, Nov. 19, 2001-Jan. 2013
Images
Less detail

Charnley type acetabular cup

https://mhc.andornot.com/en/permalink/artifact5047
Dates
1970
circa 1970
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
Accession Number
001003028
Description
Charnley type acetabular cup, which consists of a concave cup made of polyethylene; the cup has thick side edges and a flat, flared lip; the top is open; there are three concentric grooves cut into the outer edges of the cup as well as an X pattern; one side of which has a metal wire inset; the fla…
  2 images  
Accession Number
001003028
Collection
HMRC Apps Medical Research Centre Collection
Category
Diagnostic & Treatment Artifacts
Classification
Orthopedic Surgery
MeSH Heading
Orthopedic Equipment
Hip Prosthesis -- instrumentation
Description
Charnley type acetabular cup, which consists of a concave cup made of polyethylene; the cup has thick side edges and a flat, flared lip; the top is open; there are three concentric grooves cut into the outer edges of the cup as well as an X pattern; one side of which has a metal wire inset; the flared outer lip has 12 rounded notches cut out of it.
Number Of Parts
1
Provenance
Research material used at the Human Mobility Research Centre.
Dates
1970
circa 1970
Material
metal: silver
polyethylene: off-white
Inscriptions
The stamped letters "L" and "R" can be seen on the upper edge of the lip.
Permanent Location
Storage Room 0010
0010-E2-5
Dimension Notes
Depth 2.5 cm x Diam. 4.7 cm
Condition Remarks
The metal shows no corrosion; the polyethylene shows only minor wear; no staining is visible.
Copy Type
Original
Reference Types
Book
Person
JPG
Reference Comments
Dr. Charles Sorbie; "1983 Annual Product Catalogue," by Howmedica Inc., Orthopedics Division, 1983, p. A-39 (see attached photocopy); CD #3
Research Facts
This type of acetabular cup was used with cement between the bone.
Images
Less detail

82 records – page 1 of 9.